I own the Sovol SV06, it was my first printer but it was also the cheapest option for me ($169 IIRC). The Sovol has given me two problems in the entire time I used it:

1. When it came in, the extruder was jammed. Wouldn’t print or extrude any filament for some reason. Followed a 2 minute video on Sovol’s Amazon page to resolve it (although it did involve disassembling the hotend).

2. The extruder decided to encase itself in plastic one day when I printed something on it. That was a bitch and a half to clean, had to take a heat gun to it to soften the plastic then scrape it off without burning myself. My best guess is it was caused by me forgetting to run bed leveling after moving the printer a bit, hasn’t happened again.

Other than those two times it just works every time I need it. It was sitting dormant for ~3 months and I just kicked off a print yesterday, no problems. Fired right up and everything printed perfectly.

With that said, is it €239 of “Just works”? Probably not. I immediately couldn’t do some prints I planned because of the build volume (although all three of your options have the same build volume). So I’m already considering upgrading to an SV06 Plus. So check some of what you want to print that it’ll fit in 220x220x250.

I did some research on your other options and as far as I can tell, the main difference between them and the Sovol is the all metal hotend and print speed.

Sovol SV06 has an all-metal hotend so you can print high temperature filaments (PETG/TPE/CFN/etc) without worry (does require a harder nozzle most likely though). The other two seem to have some metal but are not fully metal, so if you want to hop into the more exotic materials you’ll have to upgrade those.

Second is speed, my SV06 prints at 80 mm/s. It is slow. Smallest prints take around 2-3 hours. My current print will be done after 24 hours. This is fine for me as most of my prints need complex geometry, so I’d rather it take longer and be accurate than run it too fast. The others claim a max speed of 250mm/s which would be a bit over 3x faster than the Sovol. If they can actually print at that speed without looking awful, that’s a pretty big upgrade time-wise.

If you need exotic filaments and don’t want to upgrade the hotend yourself for it then consider the Sovol. Other than that, the price in your region makes it not an option in my opinion. The Sovol just is a budget printer, only makes sense at budget prices. The Kobra and Ended you mentioned look very similar other than that, they both have auto bed leveling (a must have), same build size, very similar designs. Personally I’d lean towards the Ender, just for the community support. But do some research and see how many community member posts you see online resolved with the two. They seem to be functionally identical to me otherwise (just looking at a spec sheet, I do not have irl experience with either of these printers)

The not-so-quiet part here is “Homeless or poor people don’t deserve to have their basic need of a toilet met”

They call it a “need” but proudly talk about how they’re taking it away from the less fortunate.

South Korea’s National Security Act outlaws the praise and promotion of “anti-government” organisations.

Yikes. I’m not a fan of North Korea and I can get it if there’s some desire to prevent a fascist movement growing in SK, but this seems waaaay too broad.

Not discounted currently (I’m not convinced BF/CM aren’t all fake), but I recently got a Sovol SV06 for ~$209 from Amazon and had seen it at that price for several months, so it’ll probably come back down again.

I had one minor issue but the troubleshooting video on the Amazon page showed me how to fix it, and it’s been printing like a champ with no issues so far. FDM printer (i.e., not resin) with an all metal hotend so it can handle more exotic/stronger filament types. The auto bed leveling is also super great, most Enders don’t come with that and from what I’ve heard bed leveling is a bitch.

Also it’s been my only 3D printer ever so I don’t have much of a reference point except the ones we had in university that were almost always broken. (Or at the least unlevel)

Owning a ghost gun is a crime, right?

(Ignoring the fact that “ghost gun” is a meaningless and intentionally emotionally charged term)

In New York, yes. In the vast majority of the US, no. It’s illegal to file the serial number off an existing firearm, but 100% legal in most states to manufacture your own unserialized firearms for personal use. Just cannot be sold/transferred.

I’d note the article you linked says nothing about how many of those are actually 3D printed, it is infinitely easier to deface the serial number on an existing firearm than it is to 3D print one.

Almost always this is a player issue as mentioned. I’ve had similar issues with some files where audio just doesn’t work on one player but works fine for another. Same with subtitles. Set to an external player like VLC and see if that fixes it. (For what it’s worth, I mostly access Jellyfin from my Chromecast and I have it set to prompt me for a player each time I start watching something, one of them always works but for my files it isn’t consistent which)

Not surprised but got a source on those password claims?

Wow that is fucking awful in it’s entirety. Jesus fucking Christ, seems like just burnout and overwork are not the only issues present there. Goes a lot deeper than that with micromanagement and a “boys club” attitude, gross.

Also thank you for the link, I was so confused where to the rest of the post was.

That explains a lot, then. When I was on Vlemmy before it was deleted “All” seemed a lot more populated, now I moved to a smaller instance and it seems a lot more repetitive.

It’s a shame it works that way since everyone says the “ideal” is a ton of small instances rather than big ones.

Thanks for the clarification!

Until someone subscribes, it doesn’t exist locally and posts don’t start to flow unless there is a subscriber.

So does this mean that if I’m browsing “All” I’m not actually seeing “All” but “All from the communities/instances members of my instance subscribe to”?

I found what really helps Jellyfin on my Chromecast is setting the player manually. There’s a setting to make it ask which player to use when starting a show and if one doesn’t work, 99% of the time the other one works fine.

Sometimes switching players doesn’t fix subtitles for me, in those situations I usually have to toggle subs a few times or restart the stream and they actually work.

In my opinion it’s a minor enough inconvenience given Jellyfin is 100% free and open source, whereas Plex is tracking you and charging you. But of course maybe your media is in some more difficult format than mine.